StudioCalcs

Free · No signup · Runs in your browser

Music production calculators that give you the number

Delay in milliseconds, reverb decay, project file size, tempo in hertz: pick a calculator, type one or two values, copy the answer into your DAW. Nothing you enter is uploaded, because every number is calculated in the browser on your own machine.

All calculators

Seven tools · no account needed

Where these numbers show up in a session

  1. Locking a delay to the song

    A delay that is seven milliseconds away from the grid sounds like a mistake; the same delay locked to a dotted eighth sounds deliberate. Most DAWs have a sync button, but plenty of hardware pedals, tape echoes and plugin presets only accept a time in milliseconds. That is where the delay time calculator earns its keep.

  2. Choosing a reverb before you browse presets

    A plate, a room and a hall are not different flavours of the same thing; they decay over very different times. If you know the target RT60 for the part, you can skip two hundred presets and start from the one that already fits.

  3. Planning a render instead of guessing

    Long sessions at 96 kHz and 32-bit float get big fast. Knowing the file size before an export tells you whether the track fits on the drive you are using, and whether you should bounce stems at a lower rate.

The math behind each calculator

Every page on this site is a thin shell around one short formula. The formulas are listed below so you can check them, or work them out on a napkin when the internet is down.

Formulas used on this site
CalculatorFormula
Delay timems = 60 000 / BPM × note length in beats
Reverb time (RT60)RT60 = 0.161 × volume / (surface area × absorption)
Audio file sizebytes = seconds × sample rate × bit depth / 8 × channels
BPM to hertzHz = BPM / 60

The delay and tempo formulas assume the note length you picked. A quarter note is one beat, an eighth is 0.5, a dotted eighth is 0.75 and a triplet eighth is about 0.3333. Ping-pong delays are usually set to the dotted value because the repeats alternate between speakers, so the effective rhythm doubles.

The reverb formula is the Sabine equation, the same one used to design concert halls. It assumes a diffuse field and average absorption, so it is an estimate rather than a measurement: treat the result as the starting point for a plugin, not as a promise about how a specific room will sound. Real rooms have furniture, windows and people, and all of them eat high frequencies.

File size is exact for uncompressed audio. WAV, AIFF and BWF all store samples without compression, so the result is a hard number you can rely on when you are planning storage or a download. A 44.1 kHz, 16-bit stereo file is 176.4 KB per second; the same audio at 24-bit is 264.6 KB per second. Compressed formats such as MP3 or AAC depend on the encoder and the bitrate, so their real size will be smaller than the uncompressed figure.

Questions producers ask

What delay time should I use at 120 BPM?

A quarter note at 120 BPM is 500 ms, an eighth note is 250 ms, a dotted eighth is 375 ms and a triplet eighth is about 167 ms. A dotted eighth is the most common choice for lead lines because the repeats fall between the beats instead of on top of them.

Do I need an account to use these calculators?

No. There is no signup, no email field and no limit on how many times you can calculate. The site has no advertising and nothing is stored about what you enter.

How accurate is the reverb time estimate?

It is a Sabine calculation, which lands within roughly twenty percent in an empty, hard-surfaced room and less accurately in a furnished one. Use it to choose between a room, a plate and a hall, then trust your ears for the final setting.

Why does my exported file not match the calculator?

Check three things: whether the export is mono or stereo, whether it is 16-bit or 24-bit integer or 32-bit float, and whether the format applies any compression. A track with silence at the start or end will also be larger than the musical length suggests.

Can I use these numbers with hardware?

Yes, that is the main reason the site exists. Pedals and rack units usually want milliseconds or hertz rather than note values, so convert first and dial it in by hand.